环氧树脂防腐钢管详细介绍：1，由钢管：无缝钢管焊接钢管螺旋焊管等各类钢管2环氧树脂这款产品的涂料是一种双 - 组分，高固体分涂料由环氧树脂作为主剂。分底漆和面漆。集团由环氧树脂，颜料，添加剂和饲料的成分。乙固化剂改性的胺制备。
Epoxy resin anticorrosive steel pipe detailed introduction: 1, by steel pipe: seamless steel pipe welding steel pipe spiral welded pipe and other steel pipe 2. Epoxy resin coating of this product is a two-component, high solid content coating by epoxy resin as the main agent. Divided into primer and topcoat. The group consists of epoxy resins, pigments, additives and feed ingredients. Preparation of amine modified by B curing agent.
二，特性及应用：良好的耐用性，环氧树脂固化后漆膜坚韧，防水，性，不污染水。附着力强，具有涂层和涂膜之间的非常好的附着性。生锈优异的防水性能，具有优良的防锈材料，可保证防锈性能。随着机械强度，漆膜坚韧，具有耐磨性和耐冲击性能。高固含量，涂层厚。室温固化膜。没有大的烘烤设备。对饮用水水箱，水管，水箱，水塔供水设备内壁涂料和糖，谷物货位使用广泛适用。也可以用来作为一个游泳池，一个发电厂冷却塔并加载到燃料油，汽油，金属，混凝土内壁涂料。
2、 Characteristics and application: good durability, the cured epoxy film is tough, waterproof, non-toxic and does not pollute water. Strong adhesion and excellent adhesion between coating and film. Rust excellent waterproof performance, with excellent anti rust materials, can ensure the anti rust performance. With the mechanical strength, the film is tough, with wear resistance and impact resistance. High solid content, thick coating. Room temperature curing film. There is no big baking equipment. It is widely used for drinking water tank, water pipe, water tank, water tower, inner wall coating of water supply equipment, sugar and grain storage. It can also be used as a swimming pool, a cooling tower in a power plant and loaded with fuel oil, gasoline, metal, concrete inner wall coating.
三、技术指标： （注：耐化学试剂为底，面复合层)项目 指标 项目 指标 漆膜外观及颜色 白色、漆膜平整 抗冲击力公斤/厘米 50 粘度（涂-4粘度计）秒 >30 附着力（划圈法）级 1 干燥时间：表干（h） <2 柔韧性（mm） 1 实干（h） 24 耐3%盐水 72h 无变化 耐10%酸、碱、盐
3、 Technical indicators: (Note: chemical resistance is the base, surface composite layer) project index project index: the appearance and color of the paint film is white, the paint film is flat, the impact resistance is kg / cm 50 viscosity (coating-4 viscometer) s > 30 adhesion (circle method) level 1 drying time: surface dry (H) < 2 flexibility (mm) 1 dry (H) 24 3% salt water resistance 72 h no change, 10% acid, alkali and salt resistance
四，施工及贮存：（1）应该是画的灰尘，油污，氧化皮，清洁等。在2.5的水平，以保证涂装质量前的物体表面。禁止建设水。（2）施工配比方法如下：A组份嘴巴张开，将参加A组B股，充分搅拌均匀。固化30分钟，就可以进行涂层。（3）与使用的比例的分配材料的要求，该涂层应在8小时内完成。未完成的材料来进行密封。应该在雨天或相对温度停止施工高于75％。对于腐蚀介质严重的部位，建议多道涂刷。（4）本品应存放于阴凉干燥处，避免阳光直接照射，隔绝火源，远离热源。的贮存期十二个月，应在期限届满后，检查各项技术指标，如符合指标要求的，可以继续使用。
4、 Construction and storage: (1) should be painting dust, oil, oxide scale, cleaning, etc. At 2.5 level to ensure painting quality before the surface of the object. Construction of water is prohibited. (2) The construction proportioning method is as follows: the mouth of component A shall be opened, and the B-strand of group A shall be fully mixed. After curing for 30 minutes, the coating can be carried out. (3) The coating shall be completed within 8 hours in proportion to the distribution material requirements used. Unfinished material to seal. The construction should be stopped in rainy days or relative temperature higher than 75%. For the parts with serious corrosive medium, it is recommended to apply multiple coats. (4) This product should be stored in a cool and dry place, avoid direct sunlight, keep away from fire source and heat source. After the expiration of the storage period, the technical indicators should be checked. If the requirements meet the requirements, they can be used again.
The above wonderful content has polyurethane insulation steel pipe manufacturers http://www.sdhpgy.com Provide technical support, our website will continue to present a lot of new information for you, please remember to pay attention to us!
